Ф 1.83 X3 meters second-hand bar mill
Ball mill maintenance procedures
(a), maintenance cycle:
1, after 1 month;
2, minor repair 1 -- 3 months;
3, obtained the 12-24 months;
4, overhaul 60-120 months.
(2), content of the maintenance:
1, the: the main check the oil amount, adjust each clearance, fortified by bolts, replace the individual liner or liner wear examination, repair of the feeder.
2, minor repair: check cleaning measurement of tooth surface wear, check the liner wear, replace if necessary.
3, repair: change the incoming parts, replacement drive small gear wheel and bearing, reducer strip inspection. Big gear in run 3-5 years of use can be adjusted according to situation, hollow shaft run 3-5 years should be measured.
4, overhaul: disintegration inspection cleaning, measuring, according to the wear condition, repair or replace the big gear, hollow shaft, spherical, drive shaft and pinion and cylinder, is repaired change regulation of the electrical components, electrical equipment repair, commissioning acceptance work must be conducted.
The ball mill product parameters
規格型號
筒體轉速(r/min)
裝球量(t)
進料粒度(mm)
出料粒度(mm)
產量
電機功率(kw)
重量(t)
(t/h)
Ф900×1800
36~38
1.5
≤20
0.075-0.89
0.65-2
18.5
4.6
Ф900×3000
36
2.7
≤20
0.075-0.89
1.1-3.5
22
5.6
Ф1200×2400
36
3
≤25
0.075-0.6
1.5-4.8
30
12
Ф1200×3000
36
3.5
≤25
0.074-0.4
1.6-5
37
12.8
Ф1200×4500
32.4
5
≤25
0.074-0.4
1.6-5.8
55
13.8
Ф1500×3000
29.7
7.5
≤25
0.074-0.4
2-5
75
15.6
Ф1500×4500
27
11
≤25
0.074-0.4
3-6
110
21
Ф1500×5700
28
12
≤25
0.074-0.4
3.5-6
130
24.7
Ф1830×3000
25.4
11
≤25
0.074-0.4
4-10
130
28
Ф1830×4500
25.4
15
≤25
0.074-0.4
4.5-12
155
32
Ф1830×6400
24.1
21
≤25
0.074-0.4
6.5-15
210
34
Ф1830×7000
24.1
23
≤25
0.074-0.4
7.5-17
245
36
Ф2100×3000
23.7
15
≤25
0.074-0.4
6.5-36
155
34
Ф2100×4500
23.7
24
≤25
0.074-0.4
8-43
245
42
Ф2100×7000
23.7
26
≤25
0.074-0.4
8-48
280
50
Ф2200×4500
21.5
27
≤25
0.074-0.4
9-45
280
48.5
Ф2200×6500
21.7
35
≤25
0.074-0.4
14-26
380
52.8
Ф2200×7000
21.7
35
≤25
0.074-0.4
15-28
380
54
Ф2200×7500
21.7
35
≤25
0.074-0.4
15-30
380
56
Ф2400×3000
21
23
≤25
0.074-0.4
7-50
245
54
Ф2400×4500
21
30
≤25
0.074-0.4
8.5-60
320
65
Ф2700×4000
20.7
40
≤25
0.074-0.4
12-80
400
94
Ф2700×4500
20.7
48
≤25
0.074-0.4
12-90
430
102
Ф3200×4500
18
65
≤25
0.074-0.4
按工藝條件定
800
137
More information about second-hand ball mill, please go to http://www.theflycut.com at any time